GC Columns, Accessories & Adsorbents
- Сортировать:
- Вид таблицей
-
SNOOP® Liquid Leak Detector 20434
General descriptionSustained bubble action works even on very small leaks and vertical surfaces. Flexible snooper tube extends for hard-to-reach areas. Does not contain chlorine, aliphatic amines, or ammonium compounds. Dries clean, without staining.Other NotesFor use with volumetric (bubble) flowmeters. Also useful for checking gas delivery system plumbing for leaks. Not recommend for use upstream of capillary GC systems (an electronic leak detector is preferred).Legal InformationSNOOP is a registered trademark of Swagelok CompanyПараметрыapplication(s) gas chromatography (GC): suitable
Safety InformationWGK Germany WGK 2 Flash Point F Not applicable Flash Point C Not applicable Узнать цену -
SNOOP® Liquid Leak Detector 20640-U
NACRES: SB.54 General descriptionLiquid leak detectors are suitable to detect leaks. It is easy to use and inexpensive. When squirted on fitting, a leak becomes visible by the continuous formation of bubbles in the liquid. It is recommended to be used for leakage detection of fittings which have temperature below 100°C.Other NotesFor use with volumetric (bubble) flowmeters. Also useful for checking gas delivery system plumbing for leaks. Not recommend for use upstream of capillary GC systems (an electronic leak detector is preferred).Legal InformationSNOOP is a registered trademark of Swagelok CompanySafety InformationWGK Germany - Узнать цену -
SPB®-1 Capillary GC Column 23302-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 188 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.75 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24134-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 42 df 1.20 µm application(s) gas chromatography (GC): suitable L x I.D. 10 m x 0.20 mm matrix active group Bonded; poly(dimethyl siloxane) phase, SPB-1 column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24162
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 250 df 0.20 µm application(s) gas chromatography (GC): suitable L x I.D. 15 m x 0.20 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 108,68 € / 10 460 ₽Получить предложение -
SPB®-1 Capillary GC Column 24163
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 250 df 0.20 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.20 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 12,54 € / 1 207 ₽Получить предложение -
SPB®-1 Capillary GC Column 24229-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationPAG Capillary GC Column may be used for the separation of aliphatic alcohols on a polar stationary phase.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 152 df 0.33 µm application(s) gas chromatography (GC): suitable L x I.D. 12 m x 0.20 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24230-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationPAG Capillary GC Column may be used for the separation of aliphatic alcohols on a polar stationary phase.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 152 df 0.33 µm application(s) gas chromatography (GC): suitable L x I.D. 25 m x 0.20 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24261
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 625 df 0.10 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 475,32 € / 45 748 ₽Получить предложение -
SPB®-1 Capillary GC Column 24030-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 250 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24029
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 63 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar
Safety InformationRIDADR NONH for all modes of transport WGK Germany WGK 1 Flash Point F 214.0 °F - closed cup Flash Point C 101.1 °C - closed cup 28,56 € / 2 749 ₽Получить предложение -
SPB®-1 Capillary GC Column 24031
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 63 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 23304-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 capillary GC column may be used for herbicide determination using In-tube Solid-phase microextraction (SPME).Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal or programmed) Beta value 21 df 3.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24044
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 320 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 119,49 € / 11 500 ₽Получить предложение -
SPB®-1 Capillary GC Column 24046
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 320 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24045-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 80 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24047
eCl@ss: 32119290 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 80 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar
Safety Informationpictograms GHS09 hcodes H411 pcodes P273 RIDADR UN 3077 9 / PGIII WGK Germany WGK 1 Flash Point F 600.8 °F - closed cup Flash Point C 316.00 °C - closed cup Узнать цену -
SPB®-1 Capillary GC Column 24213-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-320 °C temperature (isothermal or programmed) Beta value 80 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 100 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24215-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal or programmed) Beta value 40 df 2.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24216-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal or programmed) Beta value 40 df 2.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 24296
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal or programmed) Beta value 16 df 5.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 275,00 € / 26 468 ₽Получить предложение -
SPB®-1 Capillary GC Column 24297
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal or programmed) Beta value 16 df 5.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25360
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 1325 df 0.10 µm application(s) gas chromatography (GC): suitable L x I.D. 15 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar
Safety Informationpictograms GHS09 hcodes H411 pcodes P273 RIDADR NONH for all modes of transport WGK Germany WGK 1 Flash Point F 600.8 °F - closed cup Flash Point C 316.00 °C - closed cup Узнать цену -
SPB®-1 Capillary GC Column 25314
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column may be used for speciation of the nitrogen compounds (quantitatively), which are polar and basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 265 df 0.50 µm application(s) gas chromatography (GC): suitable L x I.D. 15 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25315
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 265 df 0.50 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 27,10 € / 2 608 ₽Получить предложение -
SPB®-1 Capillary GC Column 25382
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column may be used for speciation of the nitrogen compounds (quantitatively), which are polar and slightly basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 265 df 0.50 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25417
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 133 df 1.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar 476,21 € / 45 834 ₽Получить предложение -
SPB®-1 Capillary GC Column 25302-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 88 df 1.50 µm application(s) gas chromatography (GC): suitable L x I.D. 15 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25303
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 88 df 1.50 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25388
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-300 °C temperature (isothermal), -60-320 °C temperature (programmed) Beta value 88 df 1.50 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar
Safety InformationRIDADR NONH for all modes of transport WGK Germany WGK 1 Flash Point F 338.0 °F - closed cup Flash Point C 170.00 °C - closed cup Узнать цену -
SPB®-1 Capillary GC Column 25341-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column may be used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-260 °C temperature (isothermal), -60-280 °C temperature (programmed) Beta value 44 df 3.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25345-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column may be used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-260 °C temperature (isothermal), -60-280 °C temperature (programmed) Beta value 27 df 5.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Capillary GC Column 25349
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-1 Capillary GC Column may be used for speciation of the nitrogen compounds (quantitatively), which are polar and is basic in nature, with chemiluminescence detection.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G1, G2, and G9 parameter -60-260 °C temperature (isothermal), -60-280 °C temperature (programmed) Beta value 27 df 5.00 µm application(s) gas chromatography (GC): suitable L x I.D. 60 m x 0.53 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar Узнать цену -
SPB®-1 Intuvo Capillary GC Column 24028INT
General descriptionApplication: This column is often used for traditional general purpose applications, where a non-polar column is required. Analytes will be separated primarily according to boiling point.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase:- Bonded
- Poly(dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
Legal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыmaterial fused silica df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(dimethyl siloxane) phase column type capillary non-polar compatibility for use with Agilent Intuvo GC Узнать цену -
SPB®-1 SULFUR Capillary GC Column 24158
General descriptionApplication: A specialized version of the SPB-1, this column was developed for analyses of sulfur gases and other volatile sulfur compounds. The column displays relatively low column bleed, which makes it compatible for use with sulfur-specific detectors.
USP Code: This column meets USP G1, G2, and G9 requirements.
Phase- Bonded
- Poly(dimethyl siloxane)
- -60 °C to 300 °C (isothermal or programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica parameter -60-300 °C temperature (isothermal or programmed) Beta value 20 df 4.00 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(dimethyl siloxane) phase Featured Industry Chemicals and Industrial Polymers
Food and Beverages
Petroleumcolumn type capillary non-polar Узнать цену -
SPB®-1000 Capillary GC Column 24313
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: The incorporation of acid functional groups into the phase lends an acidic character to this column, useful for analyses of volatile acidic compounds. It offers great performance for analyses of glycols. It is the recommended column for ethylene glycol analysis.
USP Code: This column meets USP G25 and G35 requirements.
Phase:- Bonded
- Acid-modified poly(ethylene glycol)
- 60 °C to 200 °C (isothermal) or 220 °C (programmed)
ApplicationSPB®-1000 Capillary GC Column equipped with a flame ionization detector, was used for separation of flavor compounds, in an experiment conducted to study the effect of probiotic bacteria on fermented milk products, resulting in the formation of conjugated linoleic acid (CLA), microbial growth, and organoleptic attributes like acidity, texture, and flavour.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыmaterial fused silica Agency/Method meets requirements for USP G25 and G35 parameter 60-200 °C temperature (isothermal), 60-220 °C temperature (programmed) Beta value 250 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; acid-modified poly(ethylene glycol) phase Featured Industry Agriculture
Chemicals and Industrial Polymers
Cleaning Products
Clinical
Cosmetics
Environmental
Food and Beverages
Forensics and Toxicology
Personal Carecolumn type capillary polar storage temp. 2-8°C
Safety InformationPersonal Protective Equipment Eyeshields, Gloves, type N95 (US) RIDADR NONH for all modes of transport WGK Germany WGK 3 Flash Point F Not applicable Flash Point C Not applicable 366,66 € / 35 290 ₽Получить предложение -
SPB®-1000 Capillary GC Column 25445
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: The incorporation of acid functional groups into the phase lends an acidic character to this column, useful for analyses of volatile acidic compounds. It offers great performance for analyses of glycols. It is the recommended column for ethylene glycol analysis.
USP Code: This column meets USP G25 and G35 requirements.
Phase:- Bonded
- Acid-modified poly(ethylene glycol)
- 60 °C to 200 °C (isothermal) or 220 °C (programmed)
Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G25 and G35 parameter 60-200 °C temperature (isothermal), 60-220 °C temperature (programmed) Beta value 265 df 0.50 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.53 mm matrix active group Bonded; acid-modified poly(ethylene glycol) phase Featured Industry Agriculture
Chemicals and Industrial Polymers
Cleaning Products
Clinical
Cosmetics
Environmental
Food and Beverages
Forensics and Toxicology
Personal Carecolumn type capillary polar 275,73 € / 26 538 ₽Получить предложение -
SPB®-1000 Capillary GC Column 24315
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: The incorporation of acid functional groups into the phase lends an acidic character to this column, useful for analyses of volatile acidic compounds. It offers great performance for analyses of glycols. It is the recommended column for ethylene glycol analysis.
USP Code: This column meets USP G25 and G35 requirements.
Phase:- Bonded
- Acid-modified poly(ethylene glycol)
- 60 °C to 200 °C (isothermal) or 220 °C (programmed)
ApplicationSPB®-1000 Capillary GC Column equipped with a flame ionization detector, was used for separation of flavor compounds, in an experiment conducted to study the effect of probiotic bacteria on fermented milk products, resulting in the formation of conjugated linoleic acid (CLA), microbial growth, and organoleptic attributes like acidity, texture, and flavour.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G25 and G35 parameter 60-200 °C temperature (isothermal), 60-220 °C temperature (programmed) Beta value 320 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; acid-modified poly(ethylene glycol) phase Featured Industry Agriculture
Chemicals and Industrial Polymers
Cleaning Products
Clinical
Cosmetics
Environmental
Food and Beverages
Forensics and Toxicology
Personal Carecolumn type capillary polar 2 119,89 € / 204 032 ₽Получить предложение -
SPB®-20 Capillary GC Column 24086
eCl@ss: 32119290 General descriptionApplication: This column has intermediate polarity due to the higher (20%) phenyl content, producing a different elution order of polar compounds for confirmational information. It is often used for analyses of aromatic analytes.
USP Code: This column meets USP G32 requirements.
Phase:- Bonded
- Poly(20% diphenyl/80% dimethyl siloxane)
- -25 °C to 300 °C (isothermal or programmed)
ApplicationSPB®-20 fused silica capillary column is suitable for separating amino acid and keto acid by gas chromatography coupled with mass spectrometry.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method OSHA 62, meets requirements for USP G32 parameter -25-300 °C temperature (isothermal or programmed) Beta value 250 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(20% diphenyl/80% dimethyl siloxane) phase Featured Industry Clinical
Food and Beveragescolumn type capillary intermediate polar Узнать цену -
SPB®-20 Capillary GC Column 24196-U
eCl@ss: 32119290 NACRES: SB.54 General descriptionApplication: This column has intermediate polarity due to the higher (20%) phenyl content, producing a different elution order of polar compounds for confirmational information. It is often used for analyses of aromatic analytes.
USP Code: This column meets USP G32 requirements.
Phase:- Bonded
- Poly(20% diphenyl/80% dimethyl siloxane)
- -25 °C to 300 °C (isothermal or programmed)
ApplicationSPB®-20 fused silica capillary column is suitable for separating amino acid and keto acid by gas chromatography coupled with mass spectrometry.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method OSHA 62, meets requirements for USP G32 parameter -25-300 °C temperature (isothermal or programmed) Beta value 63 df 1.00 µm application(s) gas chromatography (GC): suitable size x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(20% diphenyl/80% dimethyl siloxane) phase Featured Industry Clinical
Food and Beveragescolumn type capillary intermediate polar Узнать цену -
SPB®-20 Intuvo Capillary GC Column 24086INT
General descriptionApplication: This column has intermediate polarity due to the higher (20%) phenyl content, producing a different elution order of polar compounds for confirmational information. It is often used for analyses of aromatic analytes.
USP Code: This column meets USP G32 requirements.
Phase:- Bonded
- Poly(20% diphenyl/80% dimethyl siloxane)
- -25 °C to 300 °C (isothermal or programmed)
Legal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыmaterial fused silica df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(20% diphenyl/80% dimethyl siloxane) phase column type capillary intermediate polar compatibility for use with Agilent Intuvo GC Узнать цену -
Капиллярная газоразрядная колонка SPB-225 Supelco 24335
eCl@ss: 32119290
Общее описание
Применение: Supelco предлагает самый широкий ассортимент цианопропиловых колонок в отрасли, таких как колонка промежуточной полярности.
Код USP: Эта колонка соответствует требованиям USP G7 и G19.
Фаза:
Связанный
Поли (50% цианопропилфенил/50% диметилсилоксан)
Температура. Пределы:
От 45 °C до 220 °C (изотермическая) или 240 °C (программируемая)
Другие примечания
Дополнительные продукты:
Шприцы
Флаконы
Газоочистка и управление газовыделением
Подводящие прокладки, стекловата и специализированные ручные инструменты
Перегородки и специализированные ручные инструменты
Наконечники колонн, гайки и специализированные ручные инструменты
Юридическая информация
SPB является зарегистрированной торговой маркой компании Sigma-Aldrich Co. LLC.
ПараметрыМатериал плавленый кремнезем Материал/метод соответствует требованиям к USP G7 and G19 Параметр Температура 45-220 °C (изотермическая), температура 45-240 °C (запрограммированная) Бета-значение 250 df 0.25 µm Область применения газовая хроматография (GC): подходит L x I.D. 30 m x 0.25 mm Активная группа матрицы Связанная; поли-фаза (50% цианопропилфенил/50% диметилсилоксан) Избранная отрасль Сельское хозяйство
Экологический
Продукты питания и напиткиТип столбца капиллярный полярный Температура хранения. 2-8°C Узнать цену -
Капиллярная газоразрядная колонка SPB-225 Supelco 23329-U
eCl@ss: 32119290
Общее описание
Применение: Supelco предлагает самый широкий ассортимент цианопропиловых колонок в отрасли, таких как колонка промежуточной полярности.
Код USP: Эта колонка соответствует требованиям USP G7 и G19.
Фаза:
Связанный
Поли (50% цианопропилфенил/50% диметилсилоксан)
Температура. Пределы:
От 45 °C до 220 °C (изотермическая) или 240 °C (программируемая)
Другие примечания
Дополнительные продукты:
Шприцы
Флаконы
Газоочистка и управление газовыделением
Подводящие прокладки, стекловата и специализированные ручные инструменты
Перегородки и специализированные ручные инструменты
Наконечники колонн, гайки и специализированные ручные инструменты
Юридическая информация
SPB является зарегистрированной торговой маркой компании Sigma-Aldrich Co. LLC.
ПараметрыМатериал плавленый кремнезем Материал/метод соответствует требованиям к USP G7 and G19 Параметр Температура 45-220 °C (изотермическая), температура 45-240 °C (запрограммированная) Бета-значение 250 df 0.25 µm Область применения газовая хроматография (GC): подходит L x I.D. 15 m x 0.25 mm Активная группа матрицы Связанная; поли-фаза (50% цианопропилфенил/50% диметилсилоксан) Избранная отрасль Сельское хозяйство
Экологический
Продукты питания и напиткиТип столбца капиллярный полярный Узнать цену -
SPB®-35 Capillary GC Column 24092
eCl@ss: 32119290 General descriptionApplication: With a phenyl content of 35%, this column offers a higher polarity option compared to columns containing a lower phenyl content. This column is useful for analyses of polar compounds because they are retained longer relative to non-polar compounds.
USP Code: This column meets USP G42 requirements.
Phase:- Bonded
- Poly(35% diphenyl/65% dimethyl siloxane)
- 0 °C to 300 °C (isothermal or programmed)
ApplicationSPB®-35 fused silica capillary column may be used to determine pesticide retention times, in gas chromatography equipped with electron capture detector used for determining common pesticides like parathion-methyl, fenitrothion, chlorpyrifos, dichlofluanid, vinclozolin, chlozolinate, procymidone and iprodione in musts and wine.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G42 parameter 0-300 °C temperature (isothermal or programmed) Beta value 250 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.25 mm matrix active group Bonded; poly(35% diphenyl/65% dimethyl siloxane) phase Featured Industry Clinical
Environmental
Food and Beverages
Forensics and Toxicologycolumn type capillary intermediate polar 27,65 € / 2 661 ₽Получить предложение -
SPB®-35 Capillary GC Column 24094
eCl@ss: 32119290 General descriptionApplication: With a phenyl content of 35%, this column offers a higher polarity option compared to columns containing a lower phenyl content. This column is useful for analyses of polar compounds because they are retained longer relative to non-polar compounds.
USP Code: This column meets USP G42 requirements.
Phase:- Bonded
- Poly(35% diphenyl/65% dimethyl siloxane)
- 0 °C to 300 °C (isothermal or programmed)
ApplicationSPB®-35 fused silica capillary column may be used to determine pesticide retention times, in gas chromatography equipped with electron capture detector used for determining common pesticides like parathion-methyl, fenitrothion, chlorpyrifos, dichlofluanid, vinclozolin, chlozolinate, procymidone and iprodione in musts and wine.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G42 parameter 0-300 °C temperature (isothermal or programmed) Beta value 320 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.32 mm matrix active group Bonded; poly(35% diphenyl/65% dimethyl siloxane) phase Featured Industry Clinical
Environmental
Food and Beverages
Forensics and Toxicologycolumn type capillary intermediate polar Узнать цену -
SPB®-5 Capillary GC Column 24166
eCl@ss: 32119290 General descriptionApplication: This non-polar general purpose column provides primarily a boiling point elution order with a slight increase in selectivity, especially for aromatic compounds.
USP Code: This column meets USP G27 and G36 requirements.
Phase:- Bonded
- Poly(5% diphenyl/95% dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-5 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection. It may be used as stationary phase for determination of nivalenol and deoxynivalenol in cereals by electron-capture gas chromatography. It may also find application in being used as stationary phase in capillary column gas chromatography for determination of sterols.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G27 and G36 parameter -60-320 °C temperature (isothermal or programmed) Beta value 250 df 0.20 µm application(s) gas chromatography (GC): suitable L x I.D. 30 m x 0.20 mm matrix active group Bonded; poly(5% diphenyl/95% dimethyl siloxane) phase column type capillary non-polar 181,15 € / 17 435 ₽Получить предложение -
SPB®-5 Capillary GC Column 24032
eCl@ss: 32119290 General descriptionCapillary GC column is also known as open tubular column. The carrier gas flows through the central aperture and is unrestricted throughout the length of the column.
Application: This non-polar general purpose column provides primarily a boiling point elution order with a slight increase in selectivity, especially for aromatic compounds.
USP Code: This column meets USP G27 and G36 requirements.
Phase:- Bonded
- Poly(5% diphenyl/95% dimethyl siloxane)
- 0.32 mm I.D., <2 µm: -60 °C to 320 °C (isothermal or programmed)
- 0.32 mm I.D., 2 µm: -60 °C to 300 °C (isothermal or programmed)
- 0.53 mm I.D., <2 µm: -60 °C to 300 °C (isothermal) or 320 °C (programmed)
- 0.53 mm I.D., 2 µm: -60 °C to 260 °C (isothermal) or 280 °C (programmed)
ApplicationSPB®-5 Capillary GC Column was used for speciation of the nitrogen compounds (quantitatively), which are polar and somewhat basic in nature, with chemiluminescence detection. It may also be used as stationary phase for determination of nivalenol and deoxynivalenol in cereals by electron-capture gas chromatography. Furthermore, it may also find application in being used as stationary phase in capillary column gas chromatography for determination of sterols.Other NotesComplementary products:
Syringes
Vials
Gas Purification and Gas Management
Inlet Liners, Glass Wool, and Specialized Hand Tools
Septa and Specialized Hand Tools
Column Ferrules, Nuts, and Specialized Hand ToolsLegal InformationSPB is a registered trademark of Sigma-Aldrich Co. LLCПараметрыQuality Level 100 material fused silica Agency/Method meets requirements for USP G27 and G36 parameter -60-320 °C temperature (isothermal or programmed) Beta value 250 df 0.25 µm application(s) gas chromatography (GC): suitable L x I.D. 15 m x 0.25 mm matrix active group Bonded; poly(5% diphenyl/95% dimethyl siloxane) phase column type capillary non-polar Узнать цену
Получите коммерческое предложение в течение 1 часа
Менеджер подготовит коммерческое предложение и позвонит, если понадобится уточнить детали вашего заказа
Анна Гловацкая
Менеджер по работе с клиентами
С 2010 года мы поставляем оборудование с заводов Европы. Берем на себя все — от подбора оборудования до внедрения на предприятии
Все сотрудники имеют высшее образование, закончили ведущие химические вузы страны, такие как РХТУ им Менделеева.
У большинства компаний срок ожидания составляет 10-12 недель.
Оборудование хранится на сухом отапливаемом складе, где поддерживается ровная температура.
Работаем с PonyExpress и Деловыми линиями. Вы также можете выбрать свою транспортную компанию или забрать товар со склада в Москве.
В случае любых неполадок за свой счет выполним ремонт в сервисном центре или на заводе-изготовителе. Или бесплатно заменим прибор на новый.
Производим пуско-наладку оборудования, валидацию, обучение сотрудников. Если нужно, привлекаем инженеров с заводов- изготовителей.
